Fluid Power Standards
This Table of standards lists all standards that are directly related to Fluid Power. This is a searchable table. Either sort by column or search by word in the search box (top right)
| Committee | Components | Category 1 | Category 2 | Number | Title |
|---|---|---|---|---|---|
| MCE 11 | Fluid Seals and Their Housings | O-rings | O-rings (metric) | BS 4518:1982+A2:2014 | Specification for metric dimensions of toroidal sealing rings (O-rings) and their housings |
| MCE 11 | Fluid Seals and Their Housings | O-rings | O-rings (metric) back-ups | BS 5106:1988 | Specification of spiral anti-extrusion back-up rings and their housings |
| MCE 11 | Fluid Seals and Their Housings | Bearing housings | Housings for cylinder bearings | BS ISO 10766:2014 | HFP – Cylinders – Housing dimensions for rectangular section-cut bearing rings for pistons and rods |
| MCE 11 | Fluid Seals and Their Housings | Compatibility - fluids and seal materials | Compatibility - fluids and seal materials | BS ISO 13226:2018 | Rubber. Standard reference elastomers (SREs) for characterizing the effect of liquids on vulcanized rubbers |
| MCE 11 | Fluid Seals and Their Housings | O-rings | O-rings - sizes | BS ISO 16031-1:2002 | Aerospace fluid systems - O-rings, inch series - Inside diameters and cross- sections, tolerances and size-identification codes Part 1: Close tolerances for hydraulic systems |
| MCE 11 | Fluid Seals and Their Housings | Nomenclature-rubbers | Nomenclature-rubbers | BS ISO 1629:2013 | Rubber and latices. Nomenclature |
| MCE 11 | Fluid Seals and Their Housings | Rotary shaft seals | Rotary Shaft Lip-type Seals housings | BS ISO 16589-1:2011+ A1:2018 | Rotary shaft lip-type seals incorporating thermoplastic sealing elements Part 1: Nominal dimensions and tolerances |
| MCE 11 | Fluid Seals and Their Housings | Rotary shaft seals | Rotary Shaft Lip-type Seals - vocabulary | BS ISO 16589-2:2011 | Rotary shaft lip-type seals incorporating thermoplastic sealing elements Part 2: Vocabulary |
| MCE 11 | Fluid Seals and Their Housings | Rotary shaft seals | Rotary Shaft Lip-type Seals - handling | BS ISO 16589-3:2012+Corr April 2012 | Rotary shaft lip-type seals incorporating thermoplastic sealing elements Part 3: Storage, handling and installation |
| MCE 11 | Fluid Seals and Their Housings | Rotary shaft seals | Rotary Shaft Lip-type Seals - testing | BS ISO 16589-4:2011 | Rotary shaft lip-type seals incorporating thermoplastic sealing elements Part 4: Performance test procedures |
| MCE 11 | Fluid Seals and Their Housings | O-rings | O-rings - dimensions | BS ISO 3601-1:2012+A1:2019 | Fluid power systems – O-rings Part 1: Inside diameters, cross-sections, tolerances and designation codes |
| MCE 11 | Fluid Seals and Their Housings | O-rings | O-rings - housings | BS ISO 3601-2:2016+Corr July 2017 | Fluid Power Systems - O-rings Part 2: Housing dimensions for general applications |
| MCE 11 | Fluid Seals and Their Housings | O-rings | O-rings - quality | BS ISO 3601-3:2005+A1:2018 | Fluid Power Systems - O-rings Part 3: Quality acceptance criteria |
| MCE 11 | Fluid Seals and Their Housings | O-rings | O-rings - back-ups | BS ISO 3601-4:2008 | Fluid Power Systems - O-rings Part 4: Anti-extrusion rings (back-up rings) |
| MCE 11 | Fluid Seals and Their Housings | O-rings | O-rings - materials | BS ISO 3601-5:2015+Corr March 2017 | Fluid Power Systems - O-rings Part 5: Specification of elastomeric materials for industrial applications |
| MCE 11 | Fluid Seals and Their Housings | Reciprocating seal housings | Housings for single acting seals | BS ISO 5597:2018 | HFP – Cylinders – Dimensions and tolerances of housings for single acting piston and rod seals in reciprocating application |
| MCE 11 | Fluid Seals and Their Housings | Compatibility - fluids and seal materials | Compatibility - fluids and seal materials | BS ISO 6072:2011 | Rubber – Compatibility between hydraulic fluids and standard elastomeric materials |
| MCE 11 | Fluid Seals and Their Housings | Rotary shaft seals | Rotary Shaft Lip-type Seals - housings | BS ISO 6194-1:2007 | Rotary shaft lip-type seals incorporating elastomeric sealing elements Part 1: Nominal dimensions and tolerances |
| MCE 11 | Fluid Seals and Their Housings | Rotary shaft seals | Rotary Shaft Lip-type Seals - vocabulary | BS ISO 6194-2:2009 | Rotary shaft lip-type seals incorporating elastomeric sealing elements Part 2: Vocabulary |
| MCE 11 | Fluid Seals and Their Housings | Rotary shaft seals | Rotary Shaft Lip-type Seals -handling | BS ISO 6194-3:2009 | Rotary shaft lip-type seals incorporating elastomeric sealing elements Part 3: Storage, handling and installation |
| MCE 11 | Fluid Seals and Their Housings | Rotary shaft seals | Rotary Shaft Lip-type Seals - testing | BS ISO 6194-4:2009 | Rotary shaft lip-type seals incorporating elastomeric sealing elements Part 4: Performance test procedures |
| MCE 11 | Fluid Seals and Their Housings | Rotary shaft seals | Rotary Shaft Lip-type Seals - quality | BS ISO 6194-5:2008 | Rotary shaft lip-type seals incorporating elastomeric sealing elements Part 5: Identification of visual imperfections |
| MCE 11 | Fluid Seals and Their Housings | Reciprocating seal housings | Housings for rod wipers | BS ISO 6195:2021 | Fluid power systems and components. Cylinder-rod wiper-ring housings in reciprocating applications. Dimensions and tolerances |
| MCE 11 | Fluid Seals and Their Housings | Reciprocating seal housings | Housings for double acting piston seals | BS ISO 6547:1981 | HFP – Cylinders – Piston seal housings incorporating bearing rings – Dimensions and tolerances |
| MCE 11 | Fluid Seals and Their Housings | Reciprocating seal housings | Housings for plastic-faced piston seals | BS ISO 7425-1:2021 | Hydraulic fluid power cylinders. Dimensions and tolerances of housings for elastomer-energized, plastic-faced seals - Piston seal housings |
| MCE 11 | Fluid Seals and Their Housings | Reciprocating seal housings | Housings for plastic-faced rod seals | BS ISO 7425-2:2021 | Hydraulic fluid power cylinders. Dimensions and tolerances of housings for elastomer-energized, plastic-faced seals - Rod seal housings |
| MCE 11 | Fluid Seals and Their Housings | Vee-pack stack heights | Vee-pack stack heights | ISO 3939:1977 | Fluid Power Systems and Components - Multiple lip packing sets - Methods for measuring stack heights |
| MCE 11 | Fluid Seals and Their Housings | Reciprocating seal testing | Reciprocating seal testing | ISO 7986:1997 | HFP - Sealing devices - Standard test methods to assess the performance of seals used in oil hydraulic reciprocating applications |
| MCE 18/-/3 | Cylinders | Pneumatic | Acceptance | BS ISO 10099:2001 | PFP – Cylinders – Final examination and acceptance criteria |
| MCE 18/-/3 | Cylinders | Hydraulic | Acceptance | BS ISO 10100:2020 | HFP – Cylinders – Acceptance tests |
| MCE 18/-/3 | Cylinders | Hydraulic | Mounting Dimensions | BS ISO 10762:2015 | HFP – Cylinder mounting dimensions – 1 0 MPa (100 bar) series |
| MCE 18/-/3 | Cylinders | Hydraulic | Accessory Dimensions | BS ISO 13726:2008 | HFP – Single rod cylinders, 16 MPa (160 bar) compact series with bores from 250 to 500mm – Accessory mounting dimensions |
| MCE 18/-/3 | Cylinders | Pneumatic | Mounting Dimensions | BS ISO 15524:2011 | PFP – Cylinders – Single-rod short-stroke cylinders, 1 000 kPa (10 bar) series, bores from 20 mm to 100 mm |
| MCE 18/-/3 | Cylinders | Pneumatic | Mounting Dimensions | BS ISO 15552:2018 | PFP – Cylinders with detachable mountings, 1000 kPa (10 bar) series, bores from 32 to 320mm – Basic mounting and accessories dimensions |
| MCE 18/-/3 | Cylinders | Generic | Technical Guidance | BS ISO 16589-5:2011 | Rotary shaft lip-type seals incorporating thermoplastic sealing elements Part 5: Identification of visual imperfections |
| MCE 18/-/3 | Cylinders | Hydraulic | Mounting Dimensions | BS ISO 16656:2016 | HFP – Single rod, short-stroke cylinders with bores from 32 to 100mm for use at 10 MPa (100 bar) – Mounting dimensions |
| MCE 18/-/3 | Cylinders | Pneumatic | Mounting Dimensions | BS ISO 21287:2004 | PFP – Cylinders – Compact cylinders 1 000 kPa (10 bar) series, bores from 20 to 100mm |
| MCE 18/-/3 | Cylinders | Generic | Preffered Sizes | BS ISO 3320:2013 | Fluid power systems and components – Cylinder bores and piston rod diameters and area ratios – metric sizes |
| MCE 18/-/3 | Cylinders | Generic | Preffered Sizes | BS ISO 3320:2013 | Fluid power systems and components. Cylinder bores and piston rod diameters and area ratios. Metric series |
| MCE 18/-/3 | Cylinders | Generic | Preffered Sizes | BS ISO 4393:2015 | Fluid power systems and components – Cylinders – Basic series of piston strokes |
| MCE 18/-/3 | Cylinders | Generic | Preffered Sizes | BS ISO 4395:2009+Corr:2010 | Fluid power systems and components – Cylinder piston rod end types and dimensions |
| MCE 18/-/3 | Cylinders | Hydraulic | Mounting Dimensions | BS ISO 6020-1:2007 | HFP – Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 1: Medium series |
| MCE 18/-/3 | Cylinders | Hydraulic | Mounting Dimensions | BS ISO 6020-2:2015 | HFP – Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 2: Compact series |
| MCE 18/-/3 | Cylinders | Hydraulic | Mounting Dimensions | BS ISO 6020-3:2015 | HFP – Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 3: Compact series with bores from 250 to 500mm |
| MCE 18/-/3 | Cylinders | Hydraulic | Mounting Dimensions | BS ISO 6022:2006 | HFP – Mounting dimensions for single rod cylinders, 25 MPa (250 bar) series |
| MCE 18/-/3 | Cylinders | Generic | Identification | BS ISO 6099:2018 | Fluid power systems and components – Cylinder – Identification code for mounting dimensions and mounting types |
| MCE 18/-/3 | Cylinders | Pneumatic | Mounting Dimensions | BS ISO 6432:2015 | PFP – Single rod cylinders – 10 bar (1 000 kPa) series – Bores from 8 to 25mm – Mounting dimensions |
| MCE 18/-/3 | Cylinders | Generic | Technical Guidance | BS ISO 6505:2021 | Rubber, vulcanized or thermoplastic. Determination of tendency to adhere to and corrode metal |
| MCE 18/-/3 | Cylinders | Hydraulic | Mounting Dimensions | BS ISO 6981:1992 | HFP – Cylinders - Rod end plain eyes – Mounting dimensions |
| MCE 18/-/3 | Cylinders | Hydraulic | Accessory Dimensions | BS ISO 8132:2022 | Hydraulic fluid power. Mounting dimensions for accessories forsingle rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar)series |
| MCE 18/-/3 | Cylinders | Hydraulic | Accessory Dimensions | BS ISO 8133:2022 | Hydraulic fluid power. Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) compact series |
| MCE 18/-/3 | Cylinders | Hydraulic | Port Dimensions | BS ISO 8137:1986 | HFP – Single rod cylinders 250 bar (25 MPa) series – Port dimensions |
| MCE 18/-/3 | Cylinders | Pneumatic | Accessory Dimensions | BS ISO 8139:2018 | PFP – Cylinders – 1 000 kPa (10 bar) series – Mounting dimensions of rod end spherical eyes |
| MCE 18/-/3 | Cylinders | Pneumatic | Accessory Dimensions | BS ISO 8140:2018 | PFP – Cylinders – 1 000 kPa (10 bar) series – Mounting dimensions of rod end clevises |
| MCE 18/-/3 | Cylinders | Pneumatic | Technical Guidance | ISO 6537:1982 | PFP – Cylinder barrels – Requirements for non-ferrous metallic tubes |
| MCE 18/-/3 | Cylinders | Pneumatic | Technical Guidance | PD ISO/TR 16806:2003 | PFP – Cylinders – Load capacity of pneumatic slides and their presentation method |
| MCE 18/-/3 | Cylinders | Hydraulic | Technical Guidance | PD ISO/TS 13725:2021 | Hydraulic fluid power. Method for evaluating the buckling load of a hydraulic cylinder |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 3G 100-2.3.13:1973 | Specification for general requirements for equipment for use in aircraft – All equipment – Environmental conditions – Resistance to fire in designated fire zones | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | BS 4368-1:1998+ A1:2014 | Metallic tube connectors for fluid power and general use Part 1: Split collet compression fittings | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 4F 68:2002 | Controlled storage of vulcanised rubbers for use in aerospace applications | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 5173-100:1992 | Methods of test for rubber and plastics hoses and hose assemblies Part 100: General introduction | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 5173-102.10:1990 | Methods of test for rubber and plastics hoses and hose assemblies Part 102.10 – Hydraulic pressure tests – Hydrostatic tests for oil suction and discharge hose | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 5173-102.3:1988 | Methods of test for rubber and plastics hoses and hose assemblies Part 102.3 – Hydraulic pressure tests – Determination of volumetric expansion of fuel-dispensing pump hoses | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 5173-102.4:1990 | Methods of test for rubber and plastics hoses and hose assemblies Part 102.4 – Hydraulic pressure tests – Determination of volumetric expansion of hydraulic hoses | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 5173-102.8:1987 | Methods of test for rubber and plastics hoses and hose assemblies Part 102.8 – Hydraulic pressure tests – Pressure impulse test for rigid helix reinforced thermoplastics hoses | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 5173-103.13:1994 | Methods of test for rubber and plastics hoses and hose assemblies Part 103.13 – Physical tests Determination of resistance to fire | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 5173-103.2:1990 | Methods of test for rubber and plastics hoses and hose assemblies – Part 103.2 – Physical tests – Resistance of hoses | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 5173-103.6:1990 | Methods of test for rubber and plastics hoses and hose assemblies Part 103.6 – Physical tests - Determination of ignitability of lining | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 5173-103.7:1991 | Methods of test for rubber and plastics hoses and hose assemblies Part 103.7 – Physical tests – Determination of fracture resistance of rigid polymer helical reinforcement in thermoplastics hoses | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 5173-106.2:1990 | Methods of test for rubber and plastics hoses and hose assemblies Part 106.2 – Environmental tests – General requirements for high temperature ageing tests | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS 5200:1997+Corr July 2017 | Fluid Power Systems – specification for dimensions of hydraulic connectors and adaptors | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 5244:1986 | Recommendations for application, storage and life expiry of hydraulic rubber hoses and hose assemblies | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 5327:1976 | Specification – Swept elbow bends for fluid power applications | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS 5380:1984 | Specification for hydraulic port and stud coupling using O-ring sealing and G-series fastening threads. | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS 6537:1984 | Specification for staple type connectors for hydraulic fluid power applications | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | BS 7416:1991 | Specification for precision finished seamless cold-drawn low carbon steel tubes for use in hydraulic fluid power systems | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | BS 778:1966 | Specification for steel pipes and joints for hydraulic purposes | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | BS 7993:2011 | Twin ferrule connectors and associated tubing for 316 stainless steel systems – Specification and test methods | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS 903-A9:2020 | Methods of testing vulcanized rubber. Determination of abrasion resistance. Akron and Taber methods | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN 10226-1:2004 | Pipe threads where pressure tight joins are made on the threads Part 1: Taper external threads and parallel internal threads – Dimensions, tolerances and designation | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN 10226-2:2005 | Pipe threads where pressure tight joins are made on the threads Part 2: Taper external and internal threads – Dimensions, tolerances and designation | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN 10226-3:2005 | Pipe threads where pressure tight joins are made on the threads Part 3: Verification by means of limit gauges | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | BS EN 10305-4:2016 | Steel tubes for precision applications. Technical delivery conditions. Seamless cold drawn tubes for hydraulic and pneumatic power systems | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN 10324:2004 | Steel wire and wire products – Hose reinforcement wire | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | BS EN 1092-1:2018 | Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, PN designated. Steel flanges | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN 1765:2016 | Rubber hose assemblies for oil suction and discharge services. Specification for the assemblies | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN 853:2015 | Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN 854:2015 | Rubber hoses and hose assemblies – Textile reinforced hydraulic type – Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN 856:2015+Corr:March 2019 | Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced by hydraulic type - Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN 857:2015 | Rubber hoses and hose assemblies - Wire braid reinforced compact type for hydraulic applications - Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 10619-1:2018 | Rubber and plastics hoses and tubing. Measurement of flexibility and stiffness. Bending tests at ambient temperature | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 10619-2:2021 | Rubber and plastics hoses and tubing. Measurement of flexibility and stiffness. Bending tests at sub-ambient temperatures | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 10960:2018 | Rubber and plastics hoses – Assessment of ozone resistance under dynamic conditions | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 1179-1:2013 | Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 1179-2:2022 | Connections for general use and fluid power. Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing. Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 1179-3:2008 | Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H) | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 1179-4:2008 | Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 4: Stud ends for general use only with metal-to-metal sealing (type B) | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 1307:2008 | Rubber and plastics hoses - Minimum and maximum inside diameters and tolerances on cut-to-length hoses | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 1402:2021 | Rubber and plastics hoses and hose assemblies. Hydrostatic testing | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 1402:2021 | Rubber and plastics hoses and hose assemblies. Hydrostatic testing | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 1403:2019 | Rubber hoses, textile-reinforced, for general-purpose water applications. Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 18752:2022 | Rubber hoses and hose assemblies. Wire- or textile-reinforced single-pressure types for hydraulic applications. Specification | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 19879:2021 | Metallic tube connections for fluid power and general use. Test methods for hydraulic fluid power connections | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 228-2:2003 | Pipe threads where pressure-tight joints are not made on the threads Part 2: Verification by means of limit gauges | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 2398:2016 | Rubber hoses, textile-reinforced, for compressed air. Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 30013:2011 | Rubber and plastics hoses. Methods of exposure to laboratory light sources. Determination of changes in colour, appearance and other physical properties | |
| MCE 18/-/4 | Connectors and Components | Systems | BS EN ISO 3457:2008 | Earth-moving machinery – Guards – Definitions and requirements | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 3949:2020 | Plastics hoses and hose assemblies. Textile-reinforced types for hydraulic applications. Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 4589-2:2017 | Plastics. Determination of burning behaviour by oxygen index. Ambient-temperature test | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 4589-3:2017 | Plastics. Determination of burning behaviour by oxygen index. Elevated-temperature test | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 4671:2022 | Rubber and plastics hoses and hose assemblies. Methods of measurement of the dimensions of hoses and the lengths of hose assemblies | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 5774:2016 | Plastics hoses. Textile-reinforced types for compressed-air applications. Specification | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 6149-1:2022 | Connections for hydraulic fluid power and general use. Ports and stud ends with ISO 261 metric threads and O-ring sealing. Ports with truncated housing for O-ring seal | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 6149-2:2006+Cor 1:2007 | Connections for fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 2: Heavy-duty (S series) stud ends - Dimensions, design, test methods and requirements | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 6149-3:2006+Cor 1:2007 | Connections for fluid power and general use - Ports and stud ends with ISO 261 threads and O-ring sealing Part 3: Light-duty (L series) stud ends - Dimensions, design, test methods and requirements | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 6149-4:2017 | Connections for fluid power and general use – Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 4: Dimensions, design, test methods and requirements for external and internal hex port plugs | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 6224:2011 | Thermoplastics hoses, textile reinforced for general purpose water applications – Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 6801:2021 | Rubber and plastics hoses. Determination of volumetric expansion | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 6802:2018 | Rubber or plastics hoses and hose assemblies. Hydraulic impulse test with flexing | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 6803:2017 | Rubber or plastics hoses and hose assemblies - Hydraulic pressure impulse test without flexing | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 6806:2017 | Rubber hoses and hose assemblies for use in oil burners. Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 6808:2014 | Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids. Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 7233:2021 | Rubber and plastics hoses and hose assemblies. Determination of resistance to vacuum | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 7326:2016 | Rubber and plastic hoses – Assessment of ozone resistance under static conditions | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 7662:1996 | Rubber and plastics hoses – Determination of abrasion of lining | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 7662:1996 | Rubber and plastics hoses. Determination of abrasion of lining | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 7751:2016 | Rubber and plastics hoses and hose assemblies – Ratios of proof and burst pressure to design working pressure | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 8029:2014 | Plastics hose. General-purpose collapsible water hose, textile-reinforced. Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 8030:2014 | Rubber and plastics hoses – Method of test for flammability | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 8031:2020 | Rubber and plastics hoses and hose assemblies. Determination of electrical resistance and conductivity | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 8032:1999 | Rubber and plastics hose assemblies. Flexing combined with hydraulic impulse test (half-omega test) | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 8033:2017 | Rubber and plastics hoses – Determination of adhesion between components | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 8308:2015 | Rubber and plastics hoses and tubing. Determination of transmission of liquids through hose and tubing walls | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 8330:2022 | Rubber and plastics hoses and hose assemblies. Vocabulary | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS EN ISO 8331:2016 | Rubber and plastics hoses and hose assemblies. Guidelines for selection, storage, use and maintenance | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 8434-1:2018+Cor1:2018 | Metallic tube connections for fluid power and general use Part 1: 24° cone connectors | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 9974-1:2000 | Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 9974-2:2000 | Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 2: Stud ends with elastomeric sealing (type E) | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS EN ISO 9974-3:2000 | Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 3: Stud ends with metal-to-metal sealing (type B) | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | BS ISO 10763:2020 | HFP – Plain-end, seamless and welded precision steel tubes – Dimensions and nominal working pressures | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | BS ISO 10763:2020 | Hydraulic fluid power. Plain-end, seamless and welded precision steel tubes. Dimensions and nominal working pressures | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 12151-1:2010+A1:2017 | Connections for hydraulic fluid power and general use – Hose fittings Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 12151-2:2022 | Connections for hydraulic fluid power and general use — Hose fittings. Part 2: Hose fittings with ISO 8434-1 24° cone connector ends with O-rings | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 12151-3:2021 | Connections for hydraulic fluid power and general use. Hose fittings. Part 3 Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 12151-4:2007 | Connections for hydraulic fluid power and general use – Hose fittings Part 4: Hose fittings with ISO 6149 metric stud ends | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 12151-5:2007 | Connections for hydraulic fluid power and general use – Hose fittings Part 5: Hose fittings with ISO 8434-2 37° flared ends | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 12151-6:2009 | Connections for hydraulic fluid power and general use – Hose fittings. Part 6: Hose fittings with ISO 8434-6 60° cone ends | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 1432:2021 | Rubber, vulcanized or thermoplastic. Determination of low-temperature stiffening (Gehman test) | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 1436:2020 | Rubber hoses and hose assemblies – Wire braid reinforced hydraulic types for oil or water-based fluids – Specification | |
| MCE 18/-/4 | Connectors and Components | Quick Release Couplings | BS ISO 14540:2013 | HFP – Dimensions and requirements for screw-to-connect quick-action couplings for use at a pressure of 72 MPa (720 bar) | |
| MCE 18/-/4 | Connectors and Components | Quick Release Couplings | BS ISO 14541:2013 | HFP – Dimensions and requirements for screw-to-connect quick-action couplings for general use | |
| MCE 18/-/4 | Connectors and Components | Quick Release Couplings | BS ISO 14743:2020 | PFP – Push-in connectors for thermoplastic tubes | |
| MCE 18/-/4 | Connectors and Components | Quick Release Couplings | BS ISO 15171-1:1999 | Connections for fluid power and general use – Hydraulic couplings for diagnostic purposes Part 1: Coupling not for connection under pressure | |
| MCE 18/-/4 | Connectors and Components | Quick Release Couplings | BS ISO 15171-2:2016 | Connections for fluid power and general use – Hydraulic couplings for diagnostic purposes Part 2: Coupling with M16 x 2 end for connection under pressure | |
| MCE 18/-/4 | Connectors and Components | Quick Release Couplings | BS ISO 16028:2023 | HFP – Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) - Specifications | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS ISO 16030:2022 | Pneumatic fluid power. Connections. Ports and stud ends | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 17165-1:2007 | HFP - Hose assemblies - Part 1: Dimensions and requirements | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 1817:2022 | Rubber, vulcanized or thermoplastic. Determination of the effect of liquids | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 188:2011 | Rubber, vulcanized or thermoplastic. Accelerated ageing and heat resistance tests | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | BS ISO 18869:2017 | HFP – Test methods for couplings actuated with or without tools | |
| MCE 18/-/4 | Connectors and Components | Systems | BS ISO 21018-4:2019 | HFP – Monitoring the level of particulate contamination of the fluid Part 4: Use of the light extinction technique | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 2230:2002 | Vulcanised rubber – Guide to storage | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 23297:2017 | Thermoplastics hoses and hose assemblies – Wire or synthetic yarn reinforced single pressure types for hydraulic applications - Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 23384:2021 | Rubber and plastics hoses and hose assemblies, wire or textile reinforced types with working pressure equal or above 70 MPa (700 bar). Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 23529:2016 | Rubber. General procedures for preparing and conditioning test pieces for physical test methods | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 2781:2018 | Rubber, vulcanized or thermoplastic. Determination of density | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 28702:2008 | Rubber and plastics hoses and tubing – Textile reinforced types – Sub-ambient temperature crush test | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 37:2017 | Rubber, vulcanized or thermoplastic. Determination of tensile stress-strain properties | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 3862:2020 | Rubber hoses and hose assemblies – Rubber covered spiral wire reinforced hydraulic types for oil or water-based fluids – Specification | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 4079:2020 | Rubber hoses and hose assemblies – Textile reinforced hydraulic types for oil or water-based fluids - Specification | |
| MCE 18/-/4 | Connectors and Components | Systems | BS ISO 4397:2011 | Fluid power connectors and associated components – Nominal outside diameters of tubes and nominal hose sizes | |
| MCE 18/-/4 | Connectors and Components | Systems | BS ISO 4399:2019 | Fluid Power Systems and Components - Connectors and associated components - Nominal pressures | |
| MCE 18/-/4 | Connectors and Components | Systems | BS ISO 4411:2019 | HFP – Valves – Determination of pressure differential/flow characteristics | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 48-2:2018 | Rubber, vulcanized or thermoplastic. Determination of hardness. Hardness between 10 IRHD and 100 IRHD | |
| MCE 18/-/4 | Connectors and Components | Quick Release Couplings | BS ISO 6150:2018 | PFP – cylindrical quick-action couplings for maximum working pressures of 10, 16 and 25 bar (1, 1,6 and2,5 MPa) – Plug connecting dimensions, specifications, application guidelines and testing | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS ISO 6162-1:2012 | HFP – Flange connectors with split or one-piece flange clamps and metric or inch screws – Part 1: Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS ISO 6162-2:2018 | HFP - Flange connectors with split or one-piece flange clamps and metric or inch screws – Part 2: Flange connectors , ports and mounting surfaces for use at pressures of 42 MPa (420 bar), DN 13 to DN 127 | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS ISO 6164:2018 | HFP - Four-screw, one-piece square-flange connections for use at pressures of 42 MPa, DN 25 to 80 | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 6605:2017 | HFP – Hoses and hose assemblies – Test methods | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 6805:2020 | Rubber hoses and hose assemblies for underground mining. Wire-reinforced hydraulic types for coal mining - Specification | |
| MCE 18/-/4 | Connectors and Components | Quick Release Couplings | BS ISO 7241:2014 | HFP - Dimensions and requirements of quick-action couplings | |
| MCE 18/-/4 | Connectors and Components | Hoses | BS ISO 815-1:2019 | Rubber, vulcanized or thermoplastic. Determination of compression set. At ambient or elevated temperatures | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | BS ISO 8434-2:2007 | Metallic tube connections for fluid power and general use Part 2: 37° flared connectors | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | BS ISO 8434-3:2005 | Metallic tube connections for fluid power and general use Part 3: O-ring face seal connectors | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | BS ISO 8434-6:2009+Corr:2010 | Metallic tube connections for fluid power and general use Part 6: 60° cone connector with or without O-ring | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | BS ISO 9974-4:2016 | Connections for general use and fluid power – Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 4: Dimensions, design, test methods and requirement for external hex and internal hex port plugs | |
| MCE 18/-/4 | Connectors and Components | Hoses | ISO 11237:2017 | Rubber hoses and hose assemblies. Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids. Specification | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | ISO 11926-1:1995 | Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing Part 1: Ports with O-ring seal in truncated housing | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | ISO 11926-2:1995 | Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing Part 2: Heavy-duty (S series) stud ends | |
| MCE 18/-/4 | Connectors and Components | Ports and stud end | ISO 11926-3:1995 | Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing Part 3: Light-duty (L series) stud ends | |
| MCE 18/-/4 | Connectors and Components | Hoses | ISO/TR 11340:1994 | Rubber and rubber products – Hydraulic hose assemblies – External leakage classification for hydraulic systems | |
| MCE 18/-/4 | Connectors and Components | Hoses | PD ISO/TR 18409:2018 | HFP – Hose and hose assemblies – Method of collecting a fluid sample for analysing the cleanliness of a hose or hose assembly | |
| MCE 18/-/4 | Connectors and Components | Rigid Pipework and Couplings | PD ISO/TS 11686:2017 | Connectors for fluid power and general use – Assembly instructions for connectors with adjustable stud ends and O-ring sealing | |
| MCE 18/-/4 | Connectors and Components | Hoses | PD ISO/TS 17165-2:2018 | HFP – Hose assemblies – Part 2: Practices for hydraulic hose assemblies | |
| MCE 18/-/5 | Control Components | Pneumatic | BS 6005:1997 | Specification for moulded transparent polycarbonate bowls used in compressed air filters and lubricators |
|
| MCE 18/-/5 | Control Components | Electrical | BS 6361:1988 | Specification for three-pin plug connectors for electrically controlled fluid power equipment | |
| MCE 18/-/5 | Control Components | General | BS 6683:1985 | Guide to installation and use of valves | |
| MCE 18/-/5 | Control Components | Pneumatic | BS ISO 10041-1:2010 | PFP - Electro-pneumatic continuous flow rate control valves Part 1: Main characteristics to include in the supplier's literature | |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 10041-2:2010 | PFP - Electro-pneumatic continuous flow rate control valves - Part 2: Test methods to determine main characteristics to include in the supplier's literature |
| MCE 18/-/5 | Control Components | Pneumatic | BS ISO 10094-1:2021 | Pneumatic fluid power. Electro-pneumatic pressure control valves - Main characteristics to include in the supplier's literature | |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 10094-2:2021 | Pneumatic fluid power. Electro-pneumatic pressure control valves - Test methods to determine main characteristics to include in the supplier's literature |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valve Mounting | BS ISO 10372:1992 | HFP – Four and five-port servo valves – Mounting surfaces |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valve Test Methods | BS ISO 10770-1:2009 | Hydraulic fluid power. Electrically modulated hydraulic control valves - Test methods for four-port directional flow-control valves |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valve Test Methods | BS ISO 10770-2:2012 | Hydraulic fluid power. Electrically modulated hydraulic control valves - Test methods for three-port directional flow-control valves |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 11727:1999 | PFP – Identification of ports and control mechanisms of control valves and other components |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 12238:2023 | Pneumatic fluid power. Directional control valves. Measurement of shifting time |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 12500-1:2007 | Filters for compressed air – Test methods Part 1: Oil aerosols |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 12500-2:2007 | Filters for compressed air – Test methods Part 2: Oil vapours |
| MCE 18/-/5 | Control Components | Electrical | BS ISO 15217:2000 | Fluid power systems and components – 16mm square electrical connector with earth contact – Characteristics and requirements | |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 15218:2003 | PFP – 3/2 solenoid valves – Mounting interface surfaces |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 15407-1:2000 | PFP – Five-port directional control valves, sizes 18 and 26mm Part 1: Mounting interface surfaces without electrical connector |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 15407-2:2003 | PFP – Five-port directional control valves, sizes 18 and 26mm Part 2: Mounting interface surfaces with optional electrical connector |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valve Mounting | BS ISO 16873:2011 | HFP – Pressure switches – Mounting surfaces |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 17082:2004 | PFP - Valves - Data to be included in supplier literature |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 20145:2019 | PFP – Test method for measuring acoustic emission pressure level of exhaust silencers |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 20401:2017 | PFP – Directional control valves – Specification of pin assignments for electrical round connectors of diameters 8 and 12mm |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valve Mounting | BS ISO 4401:2005 | HFP – Four-port directional control valves – Mounting surfaces |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valve Mounting | BS ISO 5599-1:2001+Cor 1:2007 | PFP – Five-port directional control valves Part 1: Mounting interface surfaces without electrical connector |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valve Mounting | BS ISO 5599-2:2001+A1:2004+Cor 1:2007 | PFP – Five-port directional control valves Part 2: Mounting interface surfaces with optional electrical connector |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valve Mounting | BS ISO 5781:2016 | HFP – Pressure reducing valves, sequence valves, unloading valves, throttle valves and check valves – Mounting surfaces |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 5782-1:2017 | PFP – Compressed air filters Part 1: Main characteristics to be included in supplier’s literature and product marking requirements |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Test Methods | BS ISO 5782-2:1997 | PFP – Compressed air filters Part 2: Test methods to determine the main characteristics to be included in supplier’s literature |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valves | BS ISO 5783:2019 | HFP - Code for identification of valve mounting surfaces and cartridge valve cavities |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valve Mounting | BS ISO 6263:2013 | HFP – Compensated flow-control valves – Mounting surfaces |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valve Mounting | BS ISO 6264:1998 | HFP – Pressure relief valves – Mounting surfaces |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 6301-1:2017 | PFP – Compressed air lubricators Part 1: Main characteristics to be included in supplier’s literature and product marking requirements |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 6301-2:2018 | PFP – Compressed air lubricators Part 2: Test methods to determine the main characteristics to be included in supplier's literature |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 6358-1:2013+A1:2020 | PFP – Determination of flow-rate characteristics of components using compressible fluids Part 1: General rules and test methods for steady-state flow |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 6358-2:2019 | PFP – Determination of flow-rate characteristics of components using compressible fluids Part 2: Alternative test methods |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 6358-3:2014 | PFP – Determination of flow-rate characteristics of components using compressible fluids Part 3: Method for calculating steady-state flow-rate characteristics of systems |
| MCE 18/-/5 | Control Components | Pneumatic | BS ISO 6953-1:2015 | PFP – Compressed air pressure regulators and filter regulators Part 1: Main characteristics to be included in literature from suppliers and product marking requirements |
|
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 6953-2:2015 | PFP – Compressed air pressure regulators and filter regulators Part 2: Test methods to determine the main characteristics to be included in literature from suppliers |
| MCE 18/-/5 | Control Components | Pneumatic | Pneumatic Valves | BS ISO 6953-3:2013 | PFP – Compressed air pressure regulators and filter regulators Part 3: Alternative test methods for measuring the flow-rate characteristics of pressure regulators |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valves | BS ISO 7368:2016 | HFP – Two-port slip in cartridge valves - Cavities |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valves | BS ISO 7789:2007 | HFP – Two, three and four-port screw-in cartridge valves - Cavities |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valves | BS ISO 7790:2013 | HFP – Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 0,5 – Clamping dimensions |
| MCE 18/-/5 | Control Components | Pneumatic | BS ISO 8778:2003 | PFP – Standard reference atmosphere | |
| MCE 18/-/5 | Control Components | Electrical | ISO 4400:1994 | Fluid Power Systems and Components - Three-pin electrical plug connectors with earth contact - Characteristics and requirements | |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valve Test Methods | ISO 6403:1988 | HFP - Valves controlling flow and pressure - Test methods |
| MCE 18/-/5 | Control Components | Electrical | ISO 6952:1994 | Fluid Power Systems - Two-pin electrical plug connectors with earth contact - Characteristics and requirements | |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valve Mounting | ISO 9461:1992 | HFP - Identification of valve ports, sub-plates, control devices and solenoids |
| MCE 18/-/5 | Control Components | Hydraulic | Hydraulic Valves | PD ISO/TR 17209:2013 | HFP – Two, three and four port screw in cartridge valves – Cavities with ISO 725 (UN and UNF) threads |
| MCE 18/-/6 | Contamination Control | Particulate Contamination | BS 5540-3:1978 | Evaluating particulate contamination of hydraulic fluids Part 3: Methods of bottling fluid samples | |
| MCE 18/-/6 | Contamination Control | Particulate Contamination | BS 5540-6:1990 | Evaluating particulate contamination of hydraulic fluids Part 6: Method of calibrating liquid automatic particle-count instruments (using mono-sized latex spheres) |
|
| MCE 18/-/6 | Contamination Control | Particulate Contamination | BS 8465:2010 | HFP – Monitoring the level of particulate contamination – Comparison membrane technique | |
| MCE 18/-/6 | Contamination Control | BS EN ISO 14644-1:2015 | Cleanrooms and associated controlled environments - Classification of air cleanliness by particle concentration | ||
| MCE 18/-/6 | Contamination Control | Filter Elements | BS ISO 11170:2013 | HFP – Filter elements – Sequence of tests for verifying performance characteristics | |
| MCE 18/-/6 | Contamination Control | BS ISO 11171:2022 | Hydraulic fluid power. Calibration of automatic particle counters for liquids | ||
| MCE 18/-/6 | Contamination Control | Particulate Contamination | BS ISO 11500:2022 | Hydraulic fluid power. Determination of the particulate contamination level of a liquid sample by automatic particle counting using the light-extinction principle | |
| MCE 18/-/6 | Contamination Control | BS ISO 11943:2021 | Hydraulic fluid power. Online automatic particle-counting systems for liquids. Methods of calibration and validation | ||
| MCE 18/-/6 | Contamination Control | Particulate Contamination | BS ISO 12584:2013 | Aerospace – Hydraulic fluid components – Expression of particulate contamination levels | |
| MCE 18/-/6 | Contamination Control | BS ISO 12669:2017 | HFP – guidelines for determining the required cleanliness level (RCL) of a system | ||
| MCE 18/-/6 | Contamination Control | BS ISO 12829:2016 | Hydraulic spin-on filters with finite lives – Method for verifying the rated fatigue life and the rated static burst pressure of the pressure-containing envelope |
||
| MCE 18/-/6 | Contamination Control | BS ISO 13317-1:2001 | Determination of particle size distribution by gravitational liquid sedimentation methods Part 1: General principles and guidelines |
||
| MCE 18/-/6 | Contamination Control | BS ISO 13317-2:2001 | Determination of particle size distribution by gravitational liquid sedimentation methods Part 2: Fixed pipette method | ||
| MCE 18/-/6 | Contamination Control | BS ISO 13317-3:2001 | Determination of particle size distribution by gravitational liquid sedimentation methods Part 3: X-ray gravitational technique |
||
| MCE 18/-/6 | Contamination Control | BS ISO 16431:2012 | HFP – System clean-up procedures and verification of cleanliness of assembled systems |
||
| MCE 18/-/6 | Contamination Control | BS ISO 16860:2005 | HFP – Filters – Test method for differential pressure devices | ||
| MCE 18/-/6 | Contamination Control | BS ISO 16889:2022 | Hydraulic fluid power — Filters — Multi-pass method for evaluating filtration performance of a filter element | ||
| MCE 18/-/6 | Contamination Control | BS ISO 16908:2014 | Hydraulic filter element test methods – Thermal conditioning and cold start-up simulation | ||
| MCE 18/-/6 | Contamination Control | BS ISO 18237:2017 | Hydraulic fluid dehydrators – Method for evaluating water separation performance of mass transfer dehydrators |
||
| MCE 18/-/6 | Contamination Control | BS ISO 18413:2015 | HFP – Cleanliness of components – Inspection document and principles related to contaminant extraction, analysis and data reporting |
||
| MCE 18/-/6 | Contamination Control | Particulate Contamination | BS ISO 21018-1:2008 | HFP – Monitoring the level of particulate contamination of the fluid Part 1: General principles | |
| MCE 18/-/6 | Contamination Control | Particulate Contamination | BS ISO 21018-3:2008 | HFP – Monitoring the level of particulate contamination of the fluid Part 3: Use of the filter blockage technique |
|
| MCE 18/-/6 | Contamination Control | Filter Elements | BS ISO 23181:2007 | HFP – Filter elements – Determination of resistance to flow fatigue using high viscosity fluid | |
| MCE 18/-/6 | Contamination Control | BS ISO 23309:2020 | HFP – Assembled systems – Methods of cleaning lines by flushing | ||
| MCE 18/-/6 | Contamination Control | BS ISO 27407:2010 | HFP – Marking of performance characteristics on hydraulic filters | ||
| MCE 18/-/6 | Contamination Control | Filter Elements | BS ISO 2941:2009 | HFP – Filter elements – Verification of collapse/burst pressure rating | |
| MCE 18/-/6 | Contamination Control | Filter Elements | BS ISO 2942:2018 | Hydraulic fluid power. Filter elements. Verification of fabrication integrity and determination of the first bubble point | |
| MCE 18/-/6 | Contamination Control | Filter Elements | BS ISO 2943:1998 | HFP – Filter elements – Verification of material compatibility with fluids | |
| MCE 18/-/6 | Contamination Control | Filter Elements | BS ISO 3723:2015 | HFP – Filter elements – Method for end load test | |
| MCE 18/-/6 | Contamination Control | Filter Elements | BS ISO 3724:2007 | HFP – Filter elements – Determination of resistance to flow fatigue using particulate contaminant |
|
| MCE 18/-/6 | Contamination Control | BS ISO 3968:2017 | HFP – Filters – Evaluation of differential pressure versus flow characteristics | ||
| MCE 18/-/6 | Contamination Control | Particulate Contamination | BS ISO 4405:2022 | Hydraulic fluid power. Fluid contamination. Determination of particulate contamination by the gravimetric method | |
| MCE 18/-/6 | Contamination Control | BS ISO 4406:2021 | Hydraulic fluid power. Fluids. Method for coding the level of contamination by solid particles | ||
| MCE 18/-/6 | Contamination Control | Particulate Contamination | BS ISO 4407:2002 | HFP – Fluid Contamination – Determination of particulate contamination by the counting method using an optical microscope |
|
| MCE 18/-/6 | Contamination Control | BS ISO 9276-1:1998+Cor1:2006 | Representation of results of particle size analysis Part 1: Graphical representation | ||
| MCE 18/-/6 | Contamination Control | BS ISO 9276-2:2014 | Representation of results of particle size analysis - Calculation of average particle sizes/diameters and moments from particle size distributions | ||
| MCE 18/-/6 | Contamination Control | BS ISO 9276-4:2001+A1:2017 | Representation of results of particle size analysis - Characterization of a classification process | ||
| MCE 18/-/6 | Contamination Control | ISO 3722:1976 | HFP - Fluid sample containers - Qualifying and controlling cleaning methods | ||
| MCE 18/-/6 | Contamination Control | Particulate Contamination | ISO 4021:1992 | HFP - Particulate contamination analysis - Extraction of fluid samples from lines of an operating system | |
| MCE 18/-/6 | Contamination Control | PD ISO/TR 10686:2013 | HFP – Method to relate the cleanliness of a hydraulic system to the cleanliness of the components and hydraulic fluid that make up the system | ||
| MCE 18/-/6 | Contamination Control | PD ISO/TR 10949:2002 | HFP - Component cleanliness - Guidelines for achieving and controlling cleanliness of components from manufacture to installation | ||
| MCE 18/-/6 | Contamination Control | PD ISO/TR 15640:2011 | HFP – Contamination Control – General principles and guidelines for selection and application of hydraulic filters | ||
| MCE 18/-/6 | Contamination Control | PD ISO/TR 16386:2014 | Impact of changes in ISO fluid power particle counting – Contamination control and filter test standards | ||
| MCE 18/-/6 | Contamination Control | PD ISO/TR 22681:2019 | HFP – Impact and use of ISO 11171:2016 µm(b) and µm(c) particle size designations on particle count and filter test data | ||
| MCE 18/-/8 | Product Testing | Noise | BS 5944-2:1992 | Measurement of airborne noise from hydraulic fluid power systems and components - Method of test for motors | |
| MCE 18/-/8 | Product Testing | Noise | BS 5944-4:1984 | Measurement of airborne noise from hydraulic fluid power systems and components Part 4: Method of determining sound power levels from valves controlling flow and pressure |
|
| MCE 18/-/8 | Product Testing | Noise | BS 5944-5:1985 | Measurement of airborne noise from hydraulic fluid power systems and components Part 5: Simplified method of determining sound power levels from pumps using an anechoic chamber |
|
| MCE 18/-/8 | Product Testing | Pump and motor performance | BS EN ISO 9906:2012 | Rotodynamic pumps. Hydraulic performance acceptance tests. Grades 1, 2 and 3 | |
| MCE 18/-/8 | Product Testing | Noise | BS ISO 10767-1:2015 | HFP – Determination of pressure ripple levels generated in systems and components Part 1: Precision method for pumps |
|
| MCE 18/-/8 | Product Testing | Noise | BS ISO 10767-2:1999 | HFP – Determination of pressure ripple levels generated in systems and components Part 2: Simplified method for pumps | |
| MCE 18/-/8 | Product Testing | Noise | BS ISO 10767-3:1999 | HFP – Determination of pressure ripple levels generated in systems and components Part 3: Method for motors |
|
| MCE 18/-/8 | Product Testing | Valve performance | BS ISO 10770-1:2009 | HFP – Electrically modulated hydraulic control valves Part 1: Test methods for four-port directional flow control valves | |
| MCE 18/-/8 | Product Testing | Valve performance | BS ISO 10770-2:2012 | HFP – Electrically modulated hydraulic control valves Part 2: Test methods for three-way directional flow control valves | |
| MCE 18/-/8 | Product Testing | Valve performance | BS ISO 10770-3:2020 | HFP – Electrically modulated hydraulic control valves Part 3: Test methods for pressure control valves | |
| MCE 18/-/8 | Product Testing | Fatigue testing | BS ISO 10771-1:2015 | HFP – Fatigue pressure testing of metal pressure containing envelopes Part 1: Test method | |
| MCE 18/-/8 | Product Testing | Noise | BS ISO 15086-1:2001 | HFP – Determination of the fluid borne noise characteristics of components and systems Part 1: Introduction | |
| MCE 18/-/8 | Product Testing | Noise | BS ISO 15086-2:2000 | HFP – Determination of the fluid borne noise characteristics of components and systems Part 2: Measurement of speed of sound in a fluid in a pipe |
|
| MCE 18/-/8 | Product Testing | Noise | BS ISO 15086-3:2022 | Hydraulic fluid power. Determination of the fluid-borne noise characteristics of components and systems - Measurement of hydraulic impedance | |
| MCE 18/-/8 | Product Testing | Noise | BS ISO 16902-1:2003 | HFP – Test code for the determination of sound power levels using sound intensity techniques – Engineering method Part 1: Pumps | |
| MCE 18/-/8 | Product Testing | Pump and motor performance | BS ISO 17559:2003 | HFP – Electrically controlled hydraulic pumps – Test methods to determine performance characteristics | |
| MCE 18/-/8 | Product Testing | Reliability | BS ISO 19973-1:2015 | PFP – Assessment of component reliability by testing Part 1: General procedures |
|
| MCE 18/-/8 | Product Testing | Reliability | BS ISO 19973-2:2015+ A1:2019 | PFP – Assessment of component reliability by testing Part 2: Directional control valves | |
| MCE 18/-/8 | Product Testing | Reliability | BS ISO 19973-3:2015 | PFP – Assessment of component reliability by testing Part 3: Cylinders with piston rod |
|
| MCE 18/-/8 | Product Testing | Reliability | BS ISO 19973-4:2014 | PFP – Assessment of component reliability by testing Part 4: Pressure regulators | |
| MCE 18/-/8 | Product Testing | Reliability | BS ISO 19973-5:2015 | PFP – Assessment of component reliability by testing Part 5: Non-return valves, shuttle valves, dual pressure valves (and function), one-way adjustable flow control valves, quick-exhaust valves | |
| MCE 18/-/8 | Product Testing | Dimensioning | BS ISO 3019-1:2001 | HFP – Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors Part 1: Inch series shown in metric units | |
| MCE 18/-/8 | Product Testing | Dimensioning | BS ISO 3019-2:2001+Cor 1:2006 | HFP – Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors Part 2: Metric series |
|
| MCE 18/-/8 | Product Testing | Pump and motor performance | BS ISO 4392-1:2002 | HFP – Determination of characteristics of motors Part 1: At constant low speed and constant pressure | |
| MCE 18/-/8 | Product Testing | Pump and motor performance | BS ISO 4392-2:2002 | HFP – Determination of characteristics of motors Part 2: Startability | |
| MCE 18/-/8 | Product Testing | Pump and motor performance | BS ISO 4409:2019 | HFP – Positive displacement pumps, motors and integral transmissions – Methods of testing and presenting basic steady state performance | |
| MCE 18/-/8 | Product Testing | Pump and motor performance | BS ISO 8426:2008 | HFP - Positive displacement pumps and motors - Determination of derived capacity | |
| MCE 18/-/8 | Product Testing | Measurement Techniques | BS ISO 9110-1:2020 | HFP – Measurement techniques Part 1:| General measurement principles | |
| MCE 18/-/8 | Product Testing | Measurement Techniques | BS ISO 9110-2:2020 | HFP – Measurement techniques Part 2:| Measurement of average steady-state pressure | |
| MCE 18/-/8 | Product Testing | Pump and motor performance | ISO 3662:1976 | HFP - Pumps and motors, geometric displacements | |
| MCE 18/-/8 | Product Testing | Pump and motor performance | ISO 4391:1983 | HFP - Pumps, motors and integrated transmissions - Parameter definitions and letter symbols |
|
| MCE 18/-/8 | Product Testing | Pump and motor performance | ISO 4392-3:1993 | HFP - Determination of characteristics of motors Part 3: At constant flow and constant torque | |
| MCE 18/-/8 | Product Testing | Noise | ISO 4412-1:1991 | HFP - Test code for determination of airborne noise levels Part 1: Pumps | |
| MCE 18/-/8 | Product Testing | Noise | ISO 4412-2:1991 | HFP - Test code for determination of airborne noise levels Part 2: Motors | |
| MCE 18/-/8 | Product Testing | Noise | ISO 4412-3:1991 | HFP - Test code for determination of airborne noise levels Part 3: Pumps - Method using a parallel piped microphone array | |
| MCE 18/-/8 | Product Testing | Fatigue testing | ISO/TR 10771-2:2008 | Hydraulic fluid power — Fatigue pressure testing of metal pressure-containing envelopes — Part 2: Rating methods | |
| MCE 18/-/8 | Product Testing | Reliability | ISO/TR 19972-1:2009 | Hydraulic fluid power — Methods to assess the reliability of hydraulic components — Part 1: General procedures and calculation method | |
| MCE 18/-/8 | Product Testing | Reliability | PD ISO/TR 16194:2017 | Pneumatic fluid power - Assessment of component reliability by accelerated life testing - General guidelines and procedures | |
| MCE 18/-/9 | Systems and Accumulators | Hydraulic Systems | Design and Commisioning | BS 6525:1984 | Specification for design and construction of reservoirs used in hydraulic fluid power systems |
| MCE 18/-/9 | Systems and Accumulators | Hydraulic Systems | Design and Commisioning | BS 7388:1991 | Guide for prevention of leaks from hydraulic fluid power systems |
| MCE 18/-/9 | Systems and Accumulators | Hydraulic Systems | Safety | BS EN 12622:2009+A1:2013 | Safety of machine tools. Hydraulic press brakes |
| MCE 18/-/9 | Systems and Accumulators | Hydraulic Systems | Accumulators | BS EN 14359:2017 | Gas-loaded accumulators for Fluid Power applications |
| MCE 18/-/9 | Systems and Accumulators | Common Systems | Safety | BS EN 60204-1:2018 | Safety of machinery. Electrical equipment of machines - General requirements |
| MCE 18/-/9 | Systems and Accumulators | Hydraulic Systems | Safety | BS EN 693:2001 | Machine tools - Safety - Hydraulic presses |
| MCE 18/-/9 | Systems and Accumulators | Hydraulic Systems | Design and Commisioning | BS EN IEC 60545:2021 | Guidelines for commissioning and operation of hydraulic turbines, pump-turbines and storage pumps |
| MCE 18/-/9 | Systems and Accumulators | Common Systems | Safety | BS EN ISO 12100:2010 | Safety of machinery. General principles for design. Risk assessment and risk reduction |
| MCE 18/-/9 | Systems and Accumulators | Common Systems | Safety | BS EN ISO 13849-1:2015 | Safety of machinery. Safety-related parts of control systems - General principles for design |
| MCE 18/-/9 | Systems and Accumulators | Common Systems | Safety | BS EN ISO 13849-2:2012 | Safety of machinery. Safety-related parts of control systems - Validation |
| MCE 18/-/9 | Systems and Accumulators | Common Systems | Safety | BS EN ISO 14118:2018 | Safety of machinery. Prevention of unexpected start-up |
| MCE 18/-/9 | Systems and Accumulators | Common Systems | Safety | BS EN ISO 14119:2013 | Safety of machinery. Interlocking devices associated with guards. Principles for design and selection |
| MCE 18/-/9 | Systems and Accumulators | Hydraulic Systems | Safety | BS EN ISO 4413:2010 | HFP – General rules and safety requirements for systems and their components |
| MCE 18/-/9 | Systems and Accumulators | Pneumatic Systems | Safety | BS EN ISO 4414:2010 | PFP - General rules and safety requirements for systems and their components |
| MCE 18/-/9 | Systems and Accumulators | Common Systems | Symbols | BS ISO 1219-3:2016 | Fluid power systems and components - Graphical symbols and circuit diagrams - Part 3: Symbol modules and connected symbols in circuit diagrams |
| MCE 18/-/9 | Systems and Accumulators | Hydraulic Systems | Terms/Vocabulary | BS ISO 17066:2007 | Hydraulic Tools – Vocabulary |
| MCE 18/-/9 | Systems and Accumulators | Common Systems | Terms/Vocabulary | BS ISO 18582-1:2016 | Fluid power – Specification of reference dictionary – Part 1: General overview on organisation and structure |
| MCE 18/-/9 | Systems and Accumulators | Common Systems | Terms/Vocabulary | BS ISO 18582-2:2018 | Fluid power. Specification of reference dictionary - Definitions of classes and properties of pneumatics |
| MCE 18/-/9 | Systems and Accumulators | Hydraulic Systems | Accumulators | BS ISO 5596:1999 | HFP – Gas-loaded accumulators with separator – Ranges of pressures and volumes and characteristic quantities |
| MCE 18/-/9 | Systems and Accumulators | Hydraulic Systems | Safety | ISO 16368:2010 | Mobile elevating work platforms. Design, calculations, safety requirements and test methods |
| MCE 18/-/9 | Systems and Accumulators | Pneumatic Systems | Terms/Vocabulary | ISO 3857-1:1977 | Glossary of terms for compressors, pneumatic tools and machines Part 1: General |
| MCE 18/-/9 | Systems and Accumulators | Pneumatic Systems | Terms/Vocabulary | ISO 3857-3:1979 | Glossary of terms for compressors, pneumatic tools and machines Part 3 Pneumatic tools and machines |
| MCE 18/-/9 | Systems and Accumulators | Hydraulic Systems | Accumulators | PD ISO/TR 10946:2019 | HFP – Gas-loaded accumulators with separator – Selection of preferred hydraulic ports |
| MCE 18/-/9 | Systems and Accumulators | Hydraulic Systems | Application notes | PD ISO/TR 22164:2020 | HFP – Application notes for the optimisation of the energy efficiency of hydraulic systems |
| MCE 18/-/9 | Systems and Accumulators | Pneumatic Systems | Application notes | PD ISO/TR 22165:2018 | PFP – Application notes for the improvement of the energy efficiency of pneumatic systems |
| MCE 18/-/9 | Systems and Accumulators | Common Systems | Safety | PD ISO/TR 23849:2010 | Guidance on the application of ISO 13849-1 and IEC 62061 in the design of safety-related control systems for machinery |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN 14832:2005 | Petroleum and related products - Determination of the oxidation stability and corrosivity of fire-resistant phosphate ester fluids | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN 14833:2005 | Petroleum and related products - Determination of the hydrolytic stability of fire- resistant phosphate ester fluids | |
| MCE 18/-/16 | Hydraulic Fluids | Performance | BS EN ISO 12922:2020 | Lubricants, industrial oils and related products (class L). Family H (Hydraulic systems). Specifications for hydraulic fluids in categories HFAE, HFAS, HFB, HFC, HFDR and HFDU | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 14935:2020 | Petroleum and related products - Determination of wick flame persistence of fire- resistant fluids |
|
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 20623:2018 | Petroleum and related products - Determination of the extreme pressure and anti- wear properties of fluids – Four ball method (European conditions) | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 20763:2004 | Petroleum and related products - Determination of anti-wear properties of hydraulic fluids - Vane pump method |
|
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 20764:2003 | Petroleum and related products - Preparation of a test portion of high-boiling liquids for the determination of water content - Nitrogen purge method | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 20783-1:2011 | Petroleum and related products - Determination of emulsion stability of fire- resistant hydraulic fluids Part 1: Fluids in class HFAE |
|
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 20783-2: 2003 | Petroleum and related products - Determination of emulsion stability of fire- resistant hydraulic fluids Part 2: Fluids in class HFB | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 20823:2003 | Petroleum and related products - Determination of the flammability characteristics of fluids in contact with hot surfaces - Manifold ignition test |
|
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 20843:2011 | Petroleum and related products – Determination of pH of fire-resistant fluids within categories HFAE, HFAS and HFC |
|
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 20844:2015 | Petroleum and related products - Determination of the shear stability of polymer- containing oils using a diesel injector nozzle | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 4259-1:2017 | Petroleum and related products. Precision of measurement methods and results - Determination of precision data in relation to methods of test | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 4259-2:2017 | Petroleum and related products. Precision of measurement methods and results - Interpretation and application of precision data in relation to methods of test | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 4259-3:2020 | Petroleum and related products- Precision of measurement methods and results Part 3: Monitoring and verification of published precision data in relation to methods of test |
|
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 4263-1:2004 | Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test Part 1: Procedure for mineral oils |
|
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 4263-2:2003 | Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test Part 2: Procedure for category HFC hydraulic fluids |
|
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 4263-3:2015 | Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test Part 3: Anhydrous procedure for synthetic hydraulic fluids |
|
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 4263-4:2006 | Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test Part 4: Procedure of industrial gear oils | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 4404-1:2012 | Petroleum and related products – Determination of the corrosion resistance of fire- resistant hydraulic fluids Part 1: Water-containing fluids |
|
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS EN ISO 4404-2:2010 | Petroleum and related products - Determination of the corrosion resistance of fire- resistant hydraulic fluids Part 2: Non-aqueous fluids | |
| MCE 18/-/16 | Hydraulic Fluids | Classification | BS EN ISO 6743-4:2015 | Lubricants, industrial oils and related products (class L) – Classification Part 4: Family H (hydraulic systems) | |
| MCE 18/-/16 | Hydraulic Fluids | Performance | BS ISO 10050:2005 | Lubricants, industrial oils and related products (class L) – Family T (turbines) – Specifications of triaryl phosphate ester turbine control fluids (category ISO-L-TCD) |
|
| MCE 18/-/16 | Hydraulic Fluids | Performance | BS ISO 11158:2009+Corr:2010 | Lubricants, industrial oils and related products (class L) – Family H (hydraulic systems) – Specifications for HH, HL, HM, HV and HG | |
| MCE 18/-/16 | Hydraulic Fluids | Performance | BS ISO 11365:2017 | Petroleum and related products – Maintenance and use guide for triaryl phosphate ester turbine control fluids | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS ISO 13226:2018 | Rubber. Standard reference elastomers (SREs) for characterizing the effect of liquids on vulcanized rubbers | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS ISO 13357-1:2017 | Petroleum products – Determination of the filterability of lubricating oils Part 1: Procedure for oils in the presence of water | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS ISO 13357-2:2017 | Petroleum products – Determination of the filterability of lubricating oils Part 2: Procedure for dry oils |
|
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS ISO 15029-2:2018 | Petroleum and related products – Determination of spray ignition characteristics of fire-resistant fluids |
|
| MCE 18/-/16 | Hydraulic Fluids | Performance | BS ISO 15380:2016 | Lubricants, industrial oils and related products (class L) – Family H (hydraulic systems) – Specifications for categories HETG, HEPG, HEES and HEPR |
|
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS ISO 26422:2014 | Petroleum and related products – Determination of shear stability of lubricating oils containing polymers – Method using a tapered roller bearing | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS ISO 2909:2002 | Petroleum products – Calculation of viscosity index from kinematic viscosity | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS ISO 6072:2011 | Rubber – Compatibility between hydraulic fluids and standard elastomeric materials | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | BS ISO 6296:2000 | Methods of test for petroleum and its products – BS 2000-439: Determination of water – Potentiometric Karl Fischer titration method | |
| MCE 18/-/16 | Hydraulic Fluids | Classification | BS ISO 6743-1:2002 | Lubricants, industrial oils and related products (class L) – Classification Part 1: Family A (total loss systems) | |
| MCE 18/-/16 | Hydraulic Fluids | Classification | BS ISO 6743-3:2003 | Lubricants, industrial oils and related products (class L) – Classification Part 3: Family D (compressors) | |
| MCE 18/-/16 | Hydraulic Fluids | Classification | BS ISO 6743-5:2006 | Lubricants, industrial oils and related products (class L) – Classification Part 5: Family T (turbines) |
|
| MCE 18/-/16 | Hydraulic Fluids | Classification | BS ISO 6743-99:2002 | Lubricants, industrial oils and related products (class L) – Classification Part 99: General | |
| MCE 18/-/16 | Hydraulic Fluids | Performance | BS ISO 7745:2010 | HFP – Fire-resistant (FR) fluids – Requirements and guidelines for use | |
| MCE 18/-/16 | Hydraulic Fluids | Performance | BS ISO 8068:2006+A1:2019 | Lubricants, industrial oils and elated products (class L) – Family T (turbines) – Specification for lubricating oils for turbines |
|
| MCE 18/-/16 | Hydraulic Fluids | Performance | DD ISO/TS 11366:2011 | Petroleum and related products – Guidance for in-servicing of lubricating oils for steam, gas and combined-cycle turbines | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | ISO 15029-1:1999 | Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids Part 1: Spray flame persistence - Hollow-cone nozzle method | |
| MCE 18/-/16 | Hydraulic Fluids | Classification | ISO 3448:1992 | Classification for viscosity grades of industrial liquid lubricants | |
| MCE 18/-/16 | Hydraulic Fluids | Testing | ISO 6247:1998 | Petroleum products - Determination of foaming characteristics of lubricating oils | |
| MCE 18/-/16 | Hydraulic Fluids | Classification | ISO 6743-2:1981 | Lubricants, industrial oils and related products (class L) Part 2: Classification for family F (spindle bearings, bearing and associated clutches |
|
| MCE 18/-/16 | Hydraulic Fluids | Classification | PD CEN/TR 14489:2005 | Fire-resistant hydraulic fluids. Classification and specification. Guidelines on selection for the protection of safety, health and the environment |
