MCE 18/-/4 Connectors and Components
MCE 18/-/4 is the UK National Committee responsible for Connectors standards within the Fluid Power Category. Members of this committee also provide the UK view to the following international committees ISO/TC 131/SC 4 (Including Working Groups 1, 2, 3 & 4).
| Jerry Hughes | Jemlyn Limited | Committee Chairman |
| Nicky Quinn | BFPA | Committee Secretary |
| Philippa Younas | BSI | BSI Liaison |
| Representative | JCB | Committee Member |
| Representative | Hose Assembly Technology | Committee Member |
| Representative | Holmbury Limited | Committee Member |
| Representative | MOD | Committee Member |
| Representative | Gates Hydraulics | Committee Member |
| Representative | Hopespare Limited | Committee Member |
| Representative | Flowtech | Committee Member |
| Representative | Interpump Fluid Solutions | Committee Member |
| Representative | SMC UK | Committee Member |
| Representative | Fluid Power Design Solutions | Committee Member |
Blurb from committee chair about this committee
| Committee | Category | Number | Title |
|---|---|---|---|
| MCE 18/-/4 | Hoses | BS 3G 100-2.3.13:1973 | Specification for general requirements for equipment for use in aircraft – All equipment – Environmental conditions – Resistance to fire in designated fire zones |
| MCE 18/-/4 | Hoses | BS 4F 68:2002 | Controlled storage of vulcanised rubbers for use in aerospace applications |
| MCE 18/-/4 | Rigid Pipework and Couplings | BS 778:1966 | Specification for steel pipes and joints for hydraulic purposes |
| MCE 18/-/4 | Hoses | BS 903-A9:2020 | Methods of testing vulcanized rubber. Determination of abrasion resistance. Akron and Taber methods |
| MCE 18/-/4 | Rigid Pipework and Couplings | BS 4368-1:1998+ A1:2014 | Metallic tube connectors for fluid power and general use Part 1: Split collet compression fittings |
| MCE 18/-/4 | Hoses | BS 5173-100:1992 | Methods of test for rubber and plastics hoses and hose assemblies Part 100: General introduction |
| MCE 18/-/4 | Hoses | BS EN ISO 1402:2021 | Rubber and plastics hoses and hose assemblies. Hydrostatic testing |
| MCE 18/-/4 | Hoses | BS 5173-102.3:1988 | Methods of test for rubber and plastics hoses and hose assemblies Part 102.3 – Hydraulic pressure tests – Determination of volumetric expansion of fuel-dispensing pump hoses |
| MCE 18/-/4 | Hoses | BS 5173-102.4:1990 | Methods of test for rubber and plastics hoses and hose assemblies Part 102.4 – Hydraulic pressure tests – Determination of volumetric expansion of hydraulic hoses |
| MCE 18/-/4 | Hoses | BS 5173-102.8:1987 | Methods of test for rubber and plastics hoses and hose assemblies Part 102.8 – Hydraulic pressure tests – Pressure impulse test for rigid helix reinforced thermoplastics hoses |
| MCE 18/-/4 | Hoses | BS 5173-102.10:1990 | Methods of test for rubber and plastics hoses and hose assemblies Part 102.10 – Hydraulic pressure tests – Hydrostatic tests for oil suction and discharge hose |
| MCE 18/-/4 | Hoses | BS 5173-103.2:1990 | Methods of test for rubber and plastics hoses and hose assemblies – Part 103.2 – Physical tests – Resistance of hoses |
| MCE 18/-/4 | Hoses | BS 5173-103.6:1990 | Methods of test for rubber and plastics hoses and hose assemblies Part 103.6 – Physical tests - Determination of ignitability of lining |
| MCE 18/-/4 | Hoses | BS 5173-103.7:1991 | Methods of test for rubber and plastics hoses and hose assemblies Part 103.7 – Physical tests – Determination of fracture resistance of rigid polymer helical reinforcement in thermoplastics hoses |
| MCE 18/-/4 | Hoses | BS 5173-103.13:1994 | Methods of test for rubber and plastics hoses and hose assemblies Part 103.13 – Physical tests Determination of resistance to fire |
| MCE 18/-/4 | Hoses | BS 5173-106.2:1990 | Methods of test for rubber and plastics hoses and hose assemblies Part 106.2 – Environmental tests – General requirements for high temperature ageing tests |
| MCE 18/-/4 | Ports and stud end | BS 5200:1997+Corr July 2017 | Fluid Power Systems – specification for dimensions of hydraulic connectors and adaptors |
| MCE 18/-/4 | Hoses | BS 5244:1986 | Recommendations for application, storage and life expiry of hydraulic rubber hoses and hose assemblies |
| MCE 18/-/4 | Hoses | BS 5327:1976 | Specification – Swept elbow bends for fluid power applications |
| MCE 18/-/4 | Ports and stud end | BS 5380:1984 | Specification for hydraulic port and stud coupling using O-ring sealing and G-series fastening threads. |
| MCE 18/-/4 | Ports and stud end | BS 6537:1984 | Specification for staple type connectors for hydraulic fluid power applications |
| MCE 18/-/4 | Rigid Pipework and Couplings | BS 7416:1991 | Specification for precision finished seamless cold-drawn low carbon steel tubes for use in hydraulic fluid power systems |
| MCE 18/-/4 | Rigid Pipework and Couplings | BS 7993:2011 | Twin ferrule connectors and associated tubing for 316 stainless steel systems – Specification and test methods |
| MCE 18/-/4 | Hoses | BS EN 853:2015 | Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - Specification |
| MCE 18/-/4 | Hoses | BS EN 854:2015 | Rubber hoses and hose assemblies – Textile reinforced hydraulic type – Specification |
| MCE 18/-/4 | Hoses | BS EN 856:2015+Corr:March 2019 | Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced by hydraulic type - Specification |
| MCE 18/-/4 | Hoses | BS EN 857:2015 | Rubber hoses and hose assemblies - Wire braid reinforced compact type for hydraulic applications - Specification |
| MCE 18/-/4 | Rigid Pipework and Couplings | BS EN 1092-1:2018 | Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, PN designated. Steel flanges |
| MCE 18/-/4 | Hoses | BS EN 1765:2016 | Rubber hose assemblies for oil suction and discharge services. Specification for the assemblies |
| MCE 18/-/4 | Ports and stud end | BS EN 10226-1:2004 | Pipe threads where pressure tight joins are made on the threads Part 1: Taper external threads and parallel internal threads – Dimensions, tolerances and designation |
| MCE 18/-/4 | Ports and stud end | BS EN 10226-2:2005 | Pipe threads where pressure tight joins are made on the threads Part 2: Taper external and internal threads – Dimensions, tolerances and designation |
| MCE 18/-/4 | Ports and stud end | BS EN 10226-3:2005 | Pipe threads where pressure tight joins are made on the threads Part 3: Verification by means of limit gauges |
| MCE 18/-/4 | Rigid Pipework and Couplings | BS EN 10305-4:2016 | Steel tubes for precision applications. Technical delivery conditions. Seamless cold drawn tubes for hydraulic and pneumatic power systems |
| MCE 18/-/4 | Hoses | BS EN 10324:2004 | Steel wire and wire products – Hose reinforcement wire |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 228-2:2003 | Pipe threads where pressure-tight joints are not made on the threads Part 2: Verification by means of limit gauges |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 1179-1:2013 | Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 1179-2:2022 | Connections for general use and fluid power. Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing. Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 1179-3:2008 | Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H) |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 1179-4:2008 | Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 4: Stud ends for general use only with metal-to-metal sealing (type B) |
| MCE 18/-/4 | Hoses | BS EN ISO 1307:2008 | Rubber and plastics hoses - Minimum and maximum inside diameters and tolerances on cut-to-length hoses |
| MCE 18/-/4 | Hoses | BS EN ISO 1402:2021 | Rubber and plastics hoses and hose assemblies. Hydrostatic testing |
| MCE 18/-/4 | Hoses | BS EN ISO 1403:2019 | Rubber hoses, textile-reinforced, for general-purpose water applications. Specification |
| MCE 18/-/4 | Hoses | BS EN ISO 10619-1:2018 | Rubber and plastics hoses and tubing. Measurement of flexibility and stiffness. Bending tests at ambient temperature |
| MCE 18/-/4 | Hoses | BS EN ISO 2398:2016 | Rubber hoses, textile-reinforced, for compressed air. Specification |
| MCE 18/-/4 | Systems | BS EN ISO 3457:2008 | Earth-moving machinery – Guards – Definitions and requirements |
| MCE 18/-/4 | Hoses | BS EN ISO 3949:2020 | Plastics hoses and hose assemblies. Textile-reinforced types for hydraulic applications. Specification |
| MCE 18/-/4 | Hoses | BS EN ISO 4589-2:2017 | Plastics. Determination of burning behaviour by oxygen index. Ambient-temperature test |
| MCE 18/-/4 | Hoses | BS EN ISO 4589-3:2017 | Plastics. Determination of burning behaviour by oxygen index. Elevated-temperature test |
| MCE 18/-/4 | Hoses | BS EN ISO 4671:2022 | Rubber and plastics hoses and hose assemblies. Methods of measurement of the dimensions of hoses and the lengths of hose assemblies |
| MCE 18/-/4 | Hoses | BS EN ISO 5774:2016 | Plastics hoses. Textile-reinforced types for compressed-air applications. Specification |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 6149-1:2022 | Connections for hydraulic fluid power and general use. Ports and stud ends with ISO 261 metric threads and O-ring sealing. Ports with truncated housing for O-ring seal |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 6149-2:2006+Cor 1:2007 | Connections for fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 2: Heavy-duty (S series) stud ends - Dimensions, design, test methods and requirements |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 6149-3:2006+Cor 1:2007 | Connections for fluid power and general use - Ports and stud ends with ISO 261 threads and O-ring sealing Part 3: Light-duty (L series) stud ends - Dimensions, design, test methods and requirements |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 6149-4:2017 | Connections for fluid power and general use – Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 4: Dimensions, design, test methods and requirements for external and internal hex port plugs |
| MCE 18/-/4 | Hoses | BS EN ISO 6224:2011 | Thermoplastics hoses, textile reinforced for general purpose water applications – Specification |
| MCE 18/-/4 | Hoses | BS EN ISO 6802:2018 | Rubber or plastics hoses and hose assemblies. Hydraulic impulse test with flexing |
| MCE 18/-/4 | Hoses | BS EN ISO 6803:2017 | Rubber or plastics hoses and hose assemblies - Hydraulic pressure impulse test without flexing |
| MCE 18/-/4 | Hoses | BS EN ISO 6806:2017 | Rubber hoses and hose assemblies for use in oil burners. Specification |
| MCE 18/-/4 | Hoses | BS EN ISO 6808:2014 | Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids. Specification |
| MCE 18/-/4 | Hoses | BS EN ISO 7233:2021 | Rubber and plastics hoses and hose assemblies. Determination of resistance to vacuum |
| MCE 18/-/4 | Hoses | BS EN ISO 7326:2016 | Rubber and plastic hoses – Assessment of ozone resistance under static conditions |
| MCE 18/-/4 | Hoses | BS EN ISO 7662:1996 | Rubber and plastics hoses – Determination of abrasion of lining |
| MCE 18/-/4 | Hoses | BS EN ISO 7751:2016 | Rubber and plastics hoses and hose assemblies – Ratios of proof and burst pressure to design working pressure |
| MCE 18/-/4 | Hoses | BS EN ISO 8029:2014 | Plastics hose. General-purpose collapsible water hose, textile-reinforced. Specification |
| MCE 18/-/4 | Hoses | BS EN ISO 8030:2014 | Rubber and plastics hoses – Method of test for flammability |
| MCE 18/-/4 | Hoses | BS EN ISO 8031:2020 | Rubber and plastics hoses and hose assemblies. Determination of electrical resistance and conductivity |
| MCE 18/-/4 | Hoses | BS EN ISO 8032:1999 | Rubber and plastics hose assemblies. Flexing combined with hydraulic impulse test (half-omega test) |
| MCE 18/-/4 | Hoses | BS EN ISO 8033:2017 | Rubber and plastics hoses – Determination of adhesion between components |
| MCE 18/-/4 | Hoses | BS EN ISO 8308:2015 | Rubber and plastics hoses and tubing. Determination of transmission of liquids through hose and tubing walls |
| MCE 18/-/4 | Hoses | BS EN ISO 8330:2022 | Rubber and plastics hoses and hose assemblies. Vocabulary |
| MCE 18/-/4 | Hoses | BS EN ISO 8331:2016 | Rubber and plastics hoses and hose assemblies. Guidelines for selection, storage, use and maintenance |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 8434-1:2018+Cor1:2018 | Metallic tube connections for fluid power and general use Part 1: 24° cone connectors |
| MCE 18/-/4 | Hoses | BS EN ISO 30013:2011 | Rubber and plastics hoses. Methods of exposure to laboratory light sources. Determination of changes in colour, appearance and other physical properties |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 9974-1:2000 | Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 9974-2:2000 | Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 2: Stud ends with elastomeric sealing (type E) |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 9974-3:2000 | Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 3: Stud ends with metal-to-metal sealing (type B) |
| MCE 18/-/4 | Hoses | BS EN ISO 18752:2022 | Rubber hoses and hose assemblies. Wire- or textile-reinforced single-pressure types for hydraulic applications. Specification |
| MCE 18/-/4 | Ports and stud end | BS EN ISO 19879:2021 | Metallic tube connections for fluid power and general use. Test methods for hydraulic fluid power connections |
| MCE 18/-/4 | Hoses | BS ISO 37:2017 | Rubber, vulcanized or thermoplastic. Determination of tensile stress-strain properties |
| MCE 18/-/4 | Hoses | BS ISO 48-2:2018 | Rubber, vulcanized or thermoplastic. Determination of hardness. Hardness between 10 IRHD and 100 IRHD |
| MCE 18/-/4 | Hoses | BS ISO 188:2011 | Rubber, vulcanized or thermoplastic. Accelerated ageing and heat resistance tests |
| MCE 18/-/4 | Hoses | BS ISO 815-1:2019 | Rubber, vulcanized or thermoplastic. Determination of compression set. At ambient or elevated temperatures |
| MCE 18/-/4 | Hoses | BS ISO 1436:2020 | Rubber hoses and hose assemblies – Wire braid reinforced hydraulic types for oil or water-based fluids – Specification |
| MCE 18/-/4 | Hoses | BS ISO 1817:2022 | Rubber, vulcanized or thermoplastic. Determination of the effect of liquids |
| MCE 18/-/4 | Hoses | BS ISO 2230:2002 | Vulcanised rubber – Guide to storage |
| MCE 18/-/4 | Hoses | BS ISO 2781:2018 | Rubber, vulcanized or thermoplastic. Determination of density |
| MCE 18/-/4 | Hoses | BS ISO 3862:2020 | Rubber hoses and hose assemblies – Rubber covered spiral wire reinforced hydraulic types for oil or water-based fluids – Specification |
| MCE 18/-/4 | Hoses | BS ISO 4079:2020 | Rubber hoses and hose assemblies – Textile reinforced hydraulic types for oil or water-based fluids - Specification |
| MCE 18/-/4 | Systems | BS ISO 4397:2011 | Fluid power connectors and associated components – Nominal outside diameters of tubes and nominal hose sizes |
| MCE 18/-/4 | Systems | BS ISO 4399:2019 | Fluid Power Systems and Components - Connectors and associated components - Nominal pressures |
| MCE 18/-/4 | Systems | BS ISO 4411:2019 | HFP – Valves – Determination of pressure differential/flow characteristics |
| MCE 18/-/4 | Quick Release Couplings | BS ISO 6150:2018 | PFP – cylindrical quick-action couplings for maximum working pressures of 10, 16 and 25 bar (1, 1,6 and2,5 MPa) – Plug connecting dimensions, specifications, application guidelines and testing |
| MCE 18/-/4 | Ports and stud end | BS ISO 6162-1:2012 | HFP – Flange connectors with split or one-piece flange clamps and metric or inch screws – Part 1: Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 |
| MCE 18/-/4 | Ports and stud end | BS ISO 6162-2:2018 | HFP - Flange connectors with split or one-piece flange clamps and metric or inch screws – Part 2: Flange connectors , ports and mounting surfaces for use at pressures of 42 MPa (420 bar), DN 13 to DN 127 |
| MCE 18/-/4 | Ports and stud end | BS ISO 6164:2018 | HFP - Four-screw, one-piece square-flange connections for use at pressures of 42 MPa, DN 25 to 80 |
| MCE 18/-/4 | Hoses | BS ISO 6605:2017 | HFP – Hoses and hose assemblies – Test methods |
| MCE 18/-/4 | Hoses | BS ISO 6805:2020 | Rubber hoses and hose assemblies for underground mining. Wire-reinforced hydraulic types for coal mining - Specification |
| MCE 18/-/4 | Quick Release Couplings | BS ISO 7241:2014 | HFP - Dimensions and requirements of quick-action couplings |
| MCE 18/-/4 | Rigid Pipework and Couplings | BS ISO 8434-2:2007 | Metallic tube connections for fluid power and general use Part 2: 37° flared connectors |
| MCE 18/-/4 | Rigid Pipework and Couplings | BS ISO 8434-3:2005 | Metallic tube connections for fluid power and general use Part 3: O-ring face seal connectors |
| MCE 18/-/4 | Rigid Pipework and Couplings | BS ISO 8434-6:2009+Corr:2010 | Metallic tube connections for fluid power and general use Part 6: 60° cone connector with or without O-ring |
| MCE 18/-/4 | Ports and stud end | BS ISO 9974-4:2016 | Connections for general use and fluid power – Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 4: Dimensions, design, test methods and requirement for external hex and internal hex port plugs |
| MCE 18/-/4 | Rigid Pipework and Couplings | BS ISO 10763:2020 | HFP – Plain-end, seamless and welded precision steel tubes – Dimensions and nominal working pressures |
| MCE 18/-/4 | Rigid Pipework and Couplings | PD ISO/TS 11686:2017 | Connectors for fluid power and general use – Assembly instructions for connectors with adjustable stud ends and O-ring sealing |
| MCE 18/-/4 | Hoses | BS ISO 12151-1:2010+A1:2017 | Connections for hydraulic fluid power and general use – Hose fittings Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends |
| MCE 18/-/4 | Hoses | BS ISO 12151-2:2022 | Connections for hydraulic fluid power and general use — Hose fittings. Part 2: Hose fittings with ISO 8434-1 24° cone connector ends with O-rings |
| MCE 18/-/4 | Hoses | BS ISO 12151-3:2021 | Connections for hydraulic fluid power and general use. Hose fittings. Part 3 Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends |
| MCE 18/-/4 | Hoses | BS ISO 12151-4:2007 | Connections for hydraulic fluid power and general use – Hose fittings Part 4: Hose fittings with ISO 6149 metric stud ends |
| MCE 18/-/4 | Hoses | BS ISO 12151-5:2007 | Connections for hydraulic fluid power and general use – Hose fittings Part 5: Hose fittings with ISO 8434-2 37° flared ends |
| MCE 18/-/4 | Hoses | BS ISO 12151-6:2009 | Connections for hydraulic fluid power and general use – Hose fittings. Part 6: Hose fittings with ISO 8434-6 60° cone ends |
| MCE 18/-/4 | Quick Release Couplings | BS ISO 14540:2013 | HFP – Dimensions and requirements for screw-to-connect quick-action couplings for use at a pressure of 72 MPa (720 bar) |
| MCE 18/-/4 | Quick Release Couplings | BS ISO 14541:2013 | HFP – Dimensions and requirements for screw-to-connect quick-action couplings for general use |
| MCE 18/-/4 | Quick Release Couplings | BS ISO 14743:2020 | PFP – Push-in connectors for thermoplastic tubes |
| MCE 18/-/4 | Quick Release Couplings | BS ISO 15171-1:1999 | Connections for fluid power and general use – Hydraulic couplings for diagnostic purposes Part 1: Coupling not for connection under pressure |
| MCE 18/-/4 | Quick Release Couplings | BS ISO 15171-2:2016 | Connections for fluid power and general use – Hydraulic couplings for diagnostic purposes Part 2: Coupling with M16 x 2 end for connection under pressure |
| MCE 18/-/4 | Quick Release Couplings | BS ISO 16028:2023 | HFP – Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) - Specifications |
| MCE 18/-/4 | Ports and stud end | BS ISO 16030:2022 | Pneumatic fluid power. Connections. Ports and stud ends |
| MCE 18/-/4 | Hoses | BS ISO 17165-1:2007 | HFP - Hose assemblies - Part 1: Dimensions and requirements |
| MCE 18/-/4 | Hoses | PD ISO/TS 17165-2:2018 | HFP – Hose assemblies – Part 2: Practices for hydraulic hose assemblies |
| MCE 18/-/4 | Hoses | PD ISO/TR 18409:2018 | HFP – Hose and hose assemblies – Method of collecting a fluid sample for analysing the cleanliness of a hose or hose assembly |
| MCE 18/-/4 | Rigid Pipework and Couplings | BS ISO 18869:2017 | HFP – Test methods for couplings actuated with or without tools |
| MCE 18/-/4 | Hoses | BS ISO 23384:2021 | Rubber and plastics hoses and hose assemblies, wire or textile reinforced types with working pressure equal or above 70 MPa (700 bar). Specification |
| MCE 18/-/4 | Systems | BS ISO 21018-4:2019 | HFP – Monitoring the level of particulate contamination of the fluid Part 4: Use of the light extinction technique |
| MCE 18/-/4 | Hoses | BS ISO 23297:2017 | Thermoplastics hoses and hose assemblies – Wire or synthetic yarn reinforced single pressure types for hydraulic applications - Specification |
| MCE 18/-/4 | Hoses | BS ISO 23529:2016 | Rubber. General procedures for preparing and conditioning test pieces for physical test methods |
| MCE 18/-/4 | Hoses | BS ISO 28702:2008 | Rubber and plastics hoses and tubing – Textile reinforced types – Sub-ambient temperature crush test |
| MCE 18/-/4 | Hoses | BS ISO 1432:2021 | Rubber, vulcanized or thermoplastic. Determination of low-temperature stiffening (Gehman test) |
| MCE 18/-/4 | Hoses | BS EN ISO 6801:2021 | Rubber and plastics hoses. Determination of volumetric expansion |
| MCE 18/-/4 | Hoses | BS EN ISO 7662:1996 | Rubber and plastics hoses. Determination of abrasion of lining |
| MCE 18/-/4 | Rigid Pipework and Couplings | BS ISO 10763:2020 | Hydraulic fluid power. Plain-end, seamless and welded precision steel tubes. Dimensions and nominal working pressures |
| MCE 18/-/4 | Hoses | ISO/TR 11340:1994 | Rubber and rubber products – Hydraulic hose assemblies – External leakage classification for hydraulic systems |
| MCE 18/-/4 | Ports and stud end | ISO 11926-1:1995 | Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing Part 1: Ports with O-ring seal in truncated housing |
| MCE 18/-/4 | Ports and stud end | ISO 11926-2:1995 | Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing Part 2: Heavy-duty (S series) stud ends |
| MCE 18/-/4 | Ports and stud end | ISO 11926-3:1995 | Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing Part 3: Light-duty (L series) stud ends |
| MCE 18/-/4 | Hoses | ISO 11237:2017 | Rubber hoses and hose assemblies. Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids. Specification |
| MCE 18/-/4 | Hoses | BS EN ISO 10619-2:2021 | Rubber and plastics hoses and tubing. Measurement of flexibility and stiffness. Bending tests at sub-ambient temperatures |
| MCE 18/-/4 | Hoses | BS EN ISO 10960:2018 | Rubber and plastics hoses – Assessment of ozone resistance under dynamic conditions |
